Monthly Archives: July 2013

You are my sunshine

Posted on by

We decided the bathroom would be gray and yellow with oil-rubbed bronze hardware.  I had my mind set that I wanted some flowers and sun something in the bathroom.  When the girls were little, I used to sing them “You are my sunshine” a lot.  It was also on a CD we wore out, so the saying means something to the girls.  I decided to make signs for the bathroom.

I used some scrap wood we had in the back of the house and made 2 signs.

I taped off a sun, and then painted.

Then came the words.

Sealed and the final product:

 

All the Extras

Posted on by

Now that the cabinets were finished, it was the extra little things that had to be wrapped up.  We installed a light in the shower (where there was nothing).

We took down the old light fixture (Wade does NOT like these kinds of lights!) and replaced with a light above each mirror.  We waited until the very end to do this part, because I did not know how I wanted to do the mirror(s).  While I worked on the rest of the bathroom, I was thinking about what to do here.

I really liked these lights but could not see spending the money on ones like this that were oil-rubbed bronze (like everything else).  These were VERY cheap, so I bought them and spray painted them with the same paint I used on the door knobs.

 

Building Cabinets- The Sinks

Posted on by

This was the super fun part…NOT.  I dropped both sinks in and they fit like a glove!

I will not tell you ALL about the difficulties with the hardware…but the biggest thing was the distance between the holes for the water lines, and the back of the 2×6 that was supporting the cabinets, was not enough room.  There was a lot of cursing, drilling and shipping to get the faucets to fit correctly.

AND there were a lot of trips to HD to get things like a longer line for the cold water…yes, the guy in the plumbing department knew very well what I was doing by the end of this project!

Had to take a break to put the medicine cabinet together.

And I checked to make sure the drawers functioned correctly.

Here was the most difficult task of all and took more than just a day to figure out.  I had to research the building codes to find out how to correctly install an additional drain pipe.  We did not want to break apart the wall to do this, so we opted to connect it to the original pipe.  I did find out it can be no more than 30″ from the main drainage pipe.  I also learned that it did not need a J trap on the second pipe.  That is there to prevent backup from sewage gases, and the first one accomplishes that.

After a lot of curing again, and MANY more trips to HD, I was able to correctly install and tighten all the pipes so that there were no leaks.  Yay me!

And the final product!!!  Running water, draining, and all!!!

Building Cabinets- The Doors

Posted on by

As I waited for the mortar and grout to set on the counter, I continued working on the doors and drawer facings.  I had these wood knobs, and used a little metallic spray paint and some shellac to make the door knobs.

 

(Taking a break to add the grout.)

Putting the doors together.  I did not make the cuts 45% because I wanted a “farmhouse” kind of look.

I used a table saw to cut out the back so that could glue in beadboard.  I did not use the dame kind that went on the walls, instead this kind is wood that snaps together, so it was double the thickness.

I punted a bit here because I really did not know how i wanted to do this.  I glued on backing board on top of the back (and used a lot of clamps to make sure it stuck!).

Next…putting in the sinks and plumbing…

Building Cabinets- Counter Top

Posted on by

The next fun task was putting on the counter top and adding the sinks.  I wanted to tile, just because I had this vision in my mind of what the bathroom should look like.  The counter had to withstand the weight of tile, so I had to do some research on making sure the support was strong enough.

Cutting the holes in the cement board.

Whoops!  I forgot to take the middle part of the sink into account when cutting.

I decided to do the tile on a diagonal.  It takes A LOT more time, but looks better.  And yes, I cut and laid every tile out before starting on actually putting it down.

Up next…doors and hardware…